Mastering the Graco Snugride: Rethreading Click Connect 35

Have you ever found yourself struggling to rethread your car seat's straps? Fear not fellow parent, for this article is here to guide you through every nook and cranny of the process. In particular, we will be exploring how to rethread those pesky Click Connect 35 straps on a Graco Snugride.

Mastering the Graco Snugride: Rethreading Click Connect 35

Understanding the Basics

Before diving into the ins and outs of rethreading your car seat's straps, it is important to understand some basic terms:

Harness Straps

These are the thick adjustable belts that cross over your child’s shoulders and converge at a buckle between their legs.


The buckle serves as an anchor point for both lower anchorage connectors (LATCH) and/or vehicle safety belts (seat belt) used to secure child restraint systems.

Retainer Clip

This clip secures harness straps around a baby's chest instead of their neck - giving them better protection from forward-facing accidents.

Now that we've gone over these definitions let’s move onto how to correctly install our Graco Snugride with ease.

Disassembling Your Car Seat

So, you've finally decided today is "re-thread-the-car-seat" day; where do you start?

  1. The first thing you want check before each use/operation involves securely fastening flexible webbing buckles in their flat position.
  2. Remove all accessories from the seat – covers supporting pillows etcetera.
  3. Locate plastic clips directly behind cover flap lines on either side: Squeeze both ends together & pop apart noting which holes they attach too when putting back later!!
  4. Gently remove fabric cover by pulling it up outwards while pushing plastic shell frame down simultaneously so everything comes loose but stays connected!

With these steps completed successfully, let's get down dirty!

Getting Ready to Rethread

  1. We start with the harness straps that come out of the backrest of your car seat
  2. Take apart retainer clip and remove buckle from crotch strap by pulling it down through opening beneath
  3. Underneath the seat, locate attaching point for adjustable lower anchor connector (ALC) clip tab(s)
  4. Pass Harness Straps together at ALC->Run left over right behind pad and then thread each through its respective shell slot crossing around correctly.
  5. Pulling everything tightly so there is little slack – both snugly held in place using hooks provided

With all these preliminary steps successfully accomplished, we can now move onto re-threading our car seats.

Rethreading Your Graco Snugride

Finally! It’s time to rethread our Graco Snugride Click Connect 35!

  1. Starting on one side or another- Insert male end of each shoulder/harness strap into left/right slots located inside sides Seats (near head rests).
    2.Once inserted make sure are threaded properly as shown then tighten them down ensure they don't slip free: To do this grab ends nearest child -> push downward while pulling length towards vehicle rear until tightens up nicely(about a finger-width width away). 3.Repeat step above on opposite side – making sure you get same smooth insertation process!!! Clasp Buckle Harness/back piece completely removing Retainer Clip aside; Run all attached lengths straight INSIDE cover edges(placing covers anew after threading is done just complicates things more)/ 5.Straight Strap Insersion requires some patience — but doing so eliminates "knotted" headaches later because once fed far enough, ends will poke upwards ready clamping closed without delay or frustration.

Always remember to double-check all attachments - ensuring no signs of play exist anywhere- before fitting infant atop what should now be finely crafted top-of-the-range safe journey mobile throne!!!


And that concludes our guide to mastering the Graco Snugride Click Connect 35 - rethreading straps process. We hope this silly article was helpful and added some laughter to your day! Remember, safety always comes first when it comes to your child's car seat, so don't hesitate if you're unsure about any steps; consult a professional or manufacturer-manual for assistance.

Leave a Reply 0

Your email address will not be published. Required fields are marked *